dBpoweramp R15.2 Discussions

[Spoon]

Please direct all discussions relating to dBpoweramp R15.2 here.

[streammagic]

Re: dBpoweramp R15.2 Discussions

Tagging Qobus downloads is now without issues.

Peter.

[jherbert]

Re: dBpoweramp R15.2 Discussions

Re: CD Ripper files not ripping complete file

Just ran into that problem yesterday. 15.2 beta ptoduces strange results with flac encoder. Using an external Samsung drive on my iMac generates faulty very small files, using the internal drive gives proper results. Reverted back to 15.1, everything is fine again with both drives. Please see attachment for details.
Attached Files Attached Files

[Spoon]

Re: dBpoweramp R15.2 Discussions

If you rip to wave, it is the same?

[Darryl R]

Re: dBpoweramp R15.2 Discussions

Was there any resolution to this? Is it related to the drive calibration (for lack of a more precise term, something related to an offset I recall) during installation?

[Porcus]

Re: dBpoweramp R15.2 Discussions

I have experienced something like jherbert's issue above, with 15.2 beta in secure ripping mode with my Sony XL1-B firewire changer.


On a certain disc, the last track ends up with zeroes.


Looking at dBpoweramp while ripping, it goes to about 3 %, no longer;
- if set to read into lead-out, it reads Pass 1 to 3 % and returns Error
- if lead-in/lead-out unchecked, it reads to about 3 % each pass, and returns "Secure". That is pretty bad behaviour.


If I revert to Burst mode, I get a correct (AR verified) rip. Tried another drive, that is OK.




Uninstalling 15.2 beta resolves the problem, upon installing either
- 15.1 Reference, or
- 13.5 Reference
(I have no 14.x lying around)

[Porcus]

Re: dBpoweramp R15.2 Discussions

And another couple of issues:

- Re-ripping a CD previously ripped with 13.5, appending to the log: The new part is unreadable. Is this a shift to unicode or something?

- The C2 over firewire for the Sony XL1-B* is still defective. The strange thing is that it even messes up the burst rip. On a CD which verifies as accurate with burst, I would have expected that also secure mode would accept the burst pass - but no. A handful of frames to re-rip.

[Spoon]

Re: dBpoweramp R15.2 Discussions

If you enable the Start LBA, and End LBA columns, the values are the same between R15.2 and R15.1?

[Porcus]

Re: dBpoweramp R15.2 Discussions

We-e-ell. It's been a few hours since I installed 15.2 again just to try to check that.


Upon trying to read a CD from a drive, it consistently hangs. Even when I ask it to try the internal drive with its lid open.


I have uninstalled and reinstalled a few times now, and I simply cannot get 15.2 to work. Back to 15.1 - after a bit of fighting and cursing.

[Spoon]

Re: dBpoweramp R15.2 Discussions

Try right click CD Ripper icon >> run as administrator

if not work, then enable debug logging (in dbpoweramp configuration), run cd ripper until hangs, then end task cd ripper (in task manager), post the log please.

[Porcus]

Re: dBpoweramp R15.2 Discussions

Will do once this rip job is done ... maybe I should have mentioned that that computer still runs XP.
15.2 did work at some instance, but then I am quite sure I installed it atop 13.5 Reference.

[thexfile]

Re: dBpoweramp R15.2 Discussions


FLAC 1.3.1 (25-Nov-2014)

http://xiph.org/flac/changelog.html

The source is available here, official Windows binaries are supplied here.

[ffm76600]

Re: dBpoweramp R15.2 Discussions

FLAC 1.3.1 (25-Nov-2014)

http://xiph.org/flac/changelog.html

The source is available here, official Windows binaries are supplied here.

Need this update very quickly ! :smile2:

Very interesting this :

- Huge encoding speedup for i386 and x86_64 (up to 250% for 24-bit)
- Slightly improved compression of compression levels 6, 7 and 8

[thexfile]

Re: dBpoweramp R15.2 Discussions

Thank you, Spoon

Update 28th November

FLAC updated to 1.3.1
Updated to latest VS 2013 compiler for whole dBpoweramp

http://forum.dbpoweramp.com/showthread.php?34737-dBpoweramp-R15-2

[ffm76600]

Re: dBpoweramp R15.2 Discussions

Thanks Spoon for the quickly update ! :D

When the version 15.2 will available to the final step ?