title
Products            Buy            Support Forum            Professional            About            Codec Central
 
Page 1 of 3 123 LastLast
Results 1 to 15 of 41

Thread: dBpoweramp R15.2 Discussions

  1. #1
    Administrator
    Join Date
    Apr 2002
    Posts
    43,855

    dBpoweramp R15.2 Discussions

    Please direct all discussions relating to dBpoweramp R15.2 here.

  2. #2

    Re: dBpoweramp R15.2 Discussions

    Tagging Qobus downloads is now without issues.

    Peter.

  3. #3

    Join Date
    Nov 2009
    Posts
    17

    Re: dBpoweramp R15.2 Discussions

    Re: CD Ripper files not ripping complete file

    Just ran into that problem yesterday. 15.2 beta ptoduces strange results with flac encoder. Using an external Samsung drive on my iMac generates faulty very small files, using the internal drive gives proper results. Reverted back to 15.1, everything is fine again with both drives. Please see attachment for details.
    Attached Files Attached Files
    Attached Files Attached Files

  4. #4
    Administrator
    Join Date
    Apr 2002
    Posts
    43,855

    Re: dBpoweramp R15.2 Discussions

    If you rip to wave, it is the same?

  5. #5
    dBpoweramp Enthusiast
    Join Date
    Jul 2014
    Posts
    99

    Re: dBpoweramp R15.2 Discussions

    Was there any resolution to this? Is it related to the drive calibration (for lack of a more precise term, something related to an offset I recall) during installation?

  6. #6
    dBpoweramp Guru
    Join Date
    Feb 2007
    Posts
    792

    Re: dBpoweramp R15.2 Discussions

    I have experienced something like jherbert's issue above, with 15.2 beta in secure ripping mode with my Sony XL1-B firewire changer.


    On a certain disc, the last track ends up with zeroes.


    Looking at dBpoweramp while ripping, it goes to about 3 %, no longer;
    - if set to read into lead-out, it reads Pass 1 to 3 % and returns Error
    - if lead-in/lead-out unchecked, it reads to about 3 % each pass, and returns "Secure". That is pretty bad behaviour.


    If I revert to Burst mode, I get a correct (AR verified) rip. Tried another drive, that is OK.




    Uninstalling 15.2 beta resolves the problem, upon installing either
    - 15.1 Reference, or
    - 13.5 Reference
    (I have no 14.x lying around)
    Last edited by Porcus; 11-14-2014 at 05:35 AM.

  7. #7
    dBpoweramp Guru
    Join Date
    Feb 2007
    Posts
    792

    Re: dBpoweramp R15.2 Discussions

    And another couple of issues:

    - Re-ripping a CD previously ripped with 13.5, appending to the log: The new part is unreadable. Is this a shift to unicode or something?

    - The C2 over firewire for the Sony XL1-B* is still defective. The strange thing is that it even messes up the burst rip. On a CD which verifies as accurate with burst, I would have expected that also secure mode would accept the burst pass - but no. A handful of frames to re-rip.

  8. #8
    Administrator
    Join Date
    Apr 2002
    Posts
    43,855

    Re: dBpoweramp R15.2 Discussions

    If you enable the Start LBA, and End LBA columns, the values are the same between R15.2 and R15.1?

  9. #9
    dBpoweramp Guru
    Join Date
    Feb 2007
    Posts
    792

    Re: dBpoweramp R15.2 Discussions

    We-e-ell. It's been a few hours since I installed 15.2 again just to try to check that.


    Upon trying to read a CD from a drive, it consistently hangs. Even when I ask it to try the internal drive with its lid open.


    I have uninstalled and reinstalled a few times now, and I simply cannot get 15.2 to work. Back to 15.1 - after a bit of fighting and cursing.

  10. #10
    Administrator
    Join Date
    Apr 2002
    Posts
    43,855

    Re: dBpoweramp R15.2 Discussions

    Try right click CD Ripper icon >> run as administrator

    if not work, then enable debug logging (in dbpoweramp configuration), run cd ripper until hangs, then end task cd ripper (in task manager), post the log please.

  11. #11
    dBpoweramp Guru
    Join Date
    Feb 2007
    Posts
    792

    Re: dBpoweramp R15.2 Discussions

    Will do once this rip job is done ... maybe I should have mentioned that that computer still runs XP.
    15.2 did work at some instance, but then I am quite sure I installed it atop 13.5 Reference.

  12. #12
    dBpoweramp Enthusiast
    Join Date
    Jul 2010
    Posts
    176

    Re: dBpoweramp R15.2 Discussions


    FLAC 1.3.1
    (25-Nov-2014)

    http://xiph.org/flac/changelog.html

    The source is available here, official Windows binaries are supplied here.


  13. #13
    dBpoweramp Enthusiast
    Join Date
    Apr 2007
    Location
    FRANCE
    Posts
    162

    Smile Re: dBpoweramp R15.2 Discussions

    Quote Originally Posted by thexfile View Post

    FLAC 1.3.1
    (25-Nov-2014)

    http://xiph.org/flac/changelog.html

    The source is available here, official Windows binaries are supplied here.

    Need this update very quickly ! :smile2:

    Very interesting this :

    - Huge encoding speedup for i386 and x86_64 (up to 250% for 24-bit)
    - Slightly improved compression of compression levels 6, 7 and 8

  14. #14
    dBpoweramp Enthusiast
    Join Date
    Jul 2010
    Posts
    176

    Re: dBpoweramp R15.2 Discussions

    Thank you, Spoon

    Update 28th November

    FLAC updated to 1.3.1
    Updated to latest VS 2013 compiler for whole dBpoweramp
    http://forum.dbpoweramp.com/showthre...poweramp-R15-2

  15. #15
    dBpoweramp Enthusiast
    Join Date
    Apr 2007
    Location
    FRANCE
    Posts
    162

    Re: dBpoweramp R15.2 Discussions

    Thanks Spoon for the quickly update ! :D

    When the version 15.2 will available to the final step ?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •